
Some heated blankets can go in a dryer; others need to be hung or dried flat. The deciding detail is the care label for your particular blanket. Check it before washing, then follow the stated drying method and any instructions for disconnecting the controls.
Introduction
A heated blanket contains electrical components, so the familiar routine for an ordinary throw is not a reliable guide. Before laundry day, identify the model, check which parts detach, and read both the washing and drying directions. The choices below help you find the right route for your blanket.
Start here: what does your care label allow?
Start with the care label on your blanket. Find the model information and read the text as well as any laundry symbols; labels and product instructions can give more specific directions than a general review.
Locate the label before the blanket goes into the wash. It may identify the model and describe how to disconnect the controls, which wash cycle is allowed, and whether the blanket can be tumble dried or needs another drying method.
Use the label to choose a drying route and prepare the space or equipment you will need:
• If the label permits tumble drying, follow its stated dryer type, heat setting and any other restrictions. Some instructions call for removing the blanket while it is still damp and allowing it to finish drying elsewhere.
• If the instructions call for line or drip drying, follow that route rather than putting the blanket in a dryer. Read the model directions for how to support the fabric.
• If the label specifies flat drying, arrange a suitable clean, level drying area before washing. Keep the blanket disconnected until it is completely dry.
• Check separately for instructions about dry cleaning, commercial dryers, ironing and laundry products. Permission for one method does not imply permission for all of them.
If the label is missing or unreadable, find the instructions for the exact model before washing or drying it. Do not assume that hand washing, line drying or a delicate machine cycle is permitted simply because another electric blanket allows it.
Three possible routes after washing
A home dryer is permitted: a Sunbeam example
If your care tag and manual explicitly permit tumble drying, use only the dryer type and setting they specify.
Sunbeam’s FAQ and its heated-bedding instruction document IMBD21ES-B offer one example: a low, delicate tumble cycle is followed by air drying. IMBD21ES-B identifies an instruction document, not a universal care method for every Sunbeam blanket. Match the directions to the product you own; other models can specify a different method.
• The FAQ describes machine washing or hand washing after disconnecting the cord and controller, as directed.
• Its described dryer route uses a home dryer on a low, delicate cycle; the FAQ cautions against commercial or laundromat dryers for the products it discusses.
• The FAQ says to remove the item while still damp, gently restore its shape and finish drying it over a line or shower rod without clothespins. It must be completely dry before reconnection.
These are Sunbeam’s instructions for the products covered by that FAQ. Another blanket may have different directions, including a different drying route. Follow the label and manual for the model in your hands.
The label calls for line drying
If the model permits or calls for line drying, follow its directions for supporting the blanket and finishing the drying process.
• Prepare the drying location before washing so you have somewhere suitable to place the blanket.
• Follow the model’s instructions for how to drape or support it.
• Allow it to dry completely before reconnecting the controller or power cord.
• If a line or shower rod is not appropriate under your model’s instructions, use the method the instructions specify.
The label calls for flat drying
If the label calls for flat drying, choose a clean, suitable flat surface and follow any further model-specific directions.
• Arrange enough space for the blanket without compressing it into a small heap.
• Follow the instructions on shaping or handling the wet fabric; avoid twisting or wringing unless explicitly permitted.
• Wait until the entire item and connector are completely dry before reconnecting.
Before washing: disconnect and inspect
Once you know the permitted care route, prepare the blanket as its instructions direct. Start with the appliance switched off and disconnected from the wall.
Disconnect power and remove the control as directed
Unplug the power cord from the wall before handling the blanket connector. Set the cord and controls aside in a dry place.
If the instructions say the controller and cord detach, disconnect them using the stated release method. Do not pull on the cable itself or force a connector that does not come apart.
Keep the control, plug and cord out of water and out of the washer and dryer. Wash the blanket only if the instructions for that model permit it and after completing the specified preparation.
Check the blanket and connections
Look over the blanket, controller and connections before laundering. The Sunbeam FAQ tells users to check that cords are disconnected and wires have not worn through the fabric.
• Look for tears or worn fabric, especially where the wiring could be exposed.
• Check the cord, plug and connector for visible damage.
• Look for scorch marks or other signs of damage and stop using the blanket if you find them.
If there is visible damage, do not use or launder the appliance. Follow the product’s safety instructions for taking it out of service.
The washing step is a separate decision
A machine-washable blanket may still need a particular drying method. Plan both stages before you start, especially if you need to clear a flat surface or make room on a drying line.
Read the label for the approved wash method, water setting and any restrictions on detergent or other laundry products. Do not add a soak, wringing step or extra treatment unless the directions permit it.
• Machine wash: If the model permits it, use the cycle and settings specified for that blanket. Do not assume the cycle for another brand applies.
• Hand wash: If this is an approved option, follow the specific directions rather than twisting or wringing the fabric.
• Keep the controls dry: A detachable controller and power cord stay out of the wash. Make sure all required components have been disconnected first.
When is the blanket ready to reconnect?
Drying is complete only when the blanket and its connection point are fully dry. The Sunbeam FAQ expressly says not to reconnect the heated product while damp.
Keep the power cord and controller disconnected until the blanket is completely dry.
Check the fabric and the area around its connector carefully. Do not insert cotton swabs, paper or other objects into an electrical socket to test it. If any part remains damp, leave the blanket disconnected and continue the permitted drying process.
Common care mistakes to avoid
A few common shortcuts can conflict with a blanket’s care instructions:
• Commercial dryers: The Sunbeam FAQ warns against commercial or laundromat dryers for the products it describes. Check your own model’s directions before choosing a dryer.
• Wringing: Do not twist or wring the blanket when the instructions prohibit it. Follow the specified handling method for wet fabric.
• Ironing: Do not iron a heated blanket if the care label or manual prohibits it. Sunbeam’s FAQ says not to iron the product it describes.
• Dry cleaning: The Sunbeam FAQ says not to dry-clean the heated bedding it covers. Check the relevant instructions for your model.
• Laundry additives: Check the care label before adding bleach, fabric softener or other treatments. Sunbeam’s FAQ says not to use bleach for the bedding it describes.
• Using heat to dry: Never switch on or reconnect a damp heated blanket to speed up drying. Let it finish drying while disconnected.
Putting the blanket away
Once the blanket is completely dry, follow its storage instructions. Keep the controls and cord together with the blanket so the correct components and manual are easy to find later.
Before putting the blanket away, make a quick check:
• Fold or store the blanket as the model instructions describe, avoiding sharp creases where the directions warn against them.
• Keep the cord and controller dry and protected from damage. Avoid pulling or tightly straining the cord.
• Choose a clean, dry location that keeps the blanket away from moisture and pests.
• Avoid placing heavy items on the stored blanket if the instructions caution against pressure or compression.
• Before the next season, inspect the blanket, cord and connector again for visible damage before use.
Once the blanket is dry, reconnected and ready for the bed, keep its care label and model instructions handy. The next laundry day will start with a clear plan for washing, drying and storing it.
References
Sunbeam Home FAQ: https://sunbeamhome.com/en-ca/pages/faqs
Good Housekeeping: https://www.goodhousekeeping.com/what-to-buy/g69176799/best-heated-blankets/
Forbes Vetted: https://www.forbes.com/sites/forbes-personal-shopper/article/best-heated-blanket/
Sleep Foundation: https://www.sleepfoundation.org/best-bedding/best-electric-blanket